Christmas toys with their own hands c step by step directions!

By Admin | Domestic Affairs
23 April 2016

Outside, in November, the month and have a little you can start preparing to celebrate the New Year, think about New Year's menu in 2013 and about how to decorate the apartment for the new year.Today we offer you several master classes how to make Christmas toys with their own hands.

content of the article:

  • Toy "Balls-webs»
  • Toy "Kind Santa Claus»
  • toy "Christmas balls»

How to make a toy "Balls-webs" with his own hands?

Balls-webs are very original and beautiful jewelry that can be seen on many design elkah.They do not have to buy in the shops for fabulous money decorating is very easy to make at home.

To do this you will need:

  • Threads (iris, crocheting, sewing, wool);
  • Balloon desired size;
  • Glue (office, silicate or PVA);
  • scissors and needles;
  • Vaseline (fat cream or butter);
  • variety of jewelry (beads, ribbons, feathers).

Step by Step manufacturing ball-webs:

  1. Take a balloon and inflate it to the desired size.Tie him to a tail wind the thread about 10 cm long, fr
    om it you will make a loop and hang to dry.
  2. Then the surface of the ball, apply petroleum jelly, because then you will be easier to disconnect from it.
  3. Threads soak glue.This can be done in several ways.If you use colored thread, a very interesting weave.
  4. Pierce tube of glue a hot needle, so that would have happened two holes, one against another.Through these holes pull the thread (it will be smeared with glue passing through a tube);
  5. Take a convenient container and pour it into the glue.Then, soak for 10-15 minutes in her skin.Watch closely so that the thread is not tangled;
  6. dry wind the thread on the ball.Skip step 4 and well impregnate the ball glue with a sponge or brush.
  7. impregnated glue the end of the thread is fixed on the ball.You can use adhesive tape, masking tape, tape.Then wrap the thread on the ball as a ball, each turn in the other direction.If you use thick thread, it is necessary to make fewer turns, and if the fine - revolutions need to do more.While working watch out for that would thread was well wetted with adhesive.
  8. Once finished reeling again to leave the thread loops.Cut the thread and lead the ball to dry.What would the ball well dried up, it must be dried for about two days.Ready ball should be firm.Do not hang the product to dry on the heater, the material from which the balloons are made, does not like it.
  9. When the glue is dry and well cured, remove the balloon from the webs.This can be done in several ways:
  10. Using a pencil with an eraser cobweb detach from the ball.Then gently puncture needle and a ball of webs heal;
  11. Untie tail ball that he was blown away, and then cured him of cobwebs.
  12. The resulting structure can be decorated with beads, feathers, beads, ribbons and other accessories.Also, it can be painted with paint from a container.
  13. All your ball is ready.By the way, if you glue together several such balls of different sizes, it can get pretty snowman.

How to make a toy "Kind Santa Claus" with his own hands?

We have all seen what the Chinese plastic Santa Clauses crowded modern shopping malls.However, looking at them, it is not hard to believe that he might fulfill the cherished desire of the New Year.But the good fairy Santa Claus can be done by yourself.

To do this you will need:

  • Vata (in the form of beads, disks and just rolls);
  • paste.You can do it yourself: in a small amount of water diluted with 1 tablespoonstarch.Then pour boiling water (250ml), stirring constantly.Bring to a boil and give cool;
  • paints (watercolor, gouache, felt-tip pens and pencils);
  • few brushes;
  • vial of perfume, oblong;
  • Scissors PVA glue, plasticine and modeling board.

Step by Step:

  1. Take the empty bottle, and remove it from the cover.Then paste it cotton pad.To do this, drop the cotton pads in the paste, and then paste them to the bubble.
  2. future head of Santa Claus sculpt plasticine swathes her in cotton wool and dipped in paste.
  3. Give both parts to dry well, and then connect them.
  4. Paints paint the face of Santa Claus.
  5. While the paint dries, glue to coat sleeves kulechki.Then they cut out the bottom edge of the mittens.Hat for Santa Claus do half of a cotton ball soaked in a paste.
  6. Once the glue is dry, color the hat and coat of our Santa Claus.
  7. on the edge of the cotton clothes make flagella.They we very carefully glue with a toothpick.
  8. Then we glue a beard and mustache.What would beard the volume, it should be done from several layers laminated together.Each next must be slightly shorter than the previous one.We will offer you several options pattern beard
  9. all your toys ready.If you want to make a similar toy that would hang on the tree, it should be easier.Therefore, the basis for fur coats and head of Santa Claus have to do is not from a bottle and made of cotton.For this roll, and its cone in a circular shape and in obmokayte paste.And then everything is done according to the instructions.

How to make a toy « Christmas balls" with his own hands?

To produce such great balls you will need:

  • adhesive plastic;
  • plastic bottle;
  • threads or rain;
  • variety of shiny decorative elements.

instructions on making Christmas balls:

  1. By putting a plastic bottle a piece of paper so that the edges be docked perfectly.Edge sheet encircle marker.So we mark the contours of the rings that would be easier to cut.Next, cut out 4 rings, the width of each about 1 cm.
  2. Rings glue together with glue so, as shown in the photo:
  3. Now you can start to decorate our balls.They can be pasted variety of sequins, beads, foil ribbons.It all depends on your desires and fantasies.

Making Christmas toys with their own hands is very interesting and exciting.Besides, this session can attract and children.We wish all the interesting ideas and success!

If you like our article and you have any thoughts about it, share it with us!For us it is very important to know your opinion!